Can I Set Up a Tub Myself? Considerations And Also Steps
Can I Set Up a Tub Myself? Considerations And Also Steps
Blog Article
The author is making several great observations related to How to Install a Bathtub Yourself overall in the article in the next paragraphs.
Installing a tub isn't specifically rocket science, yet it does call for solid plumbing, woodworking, and in some cases, tiling abilities. Changing an old tub with a brand-new one is also a moderately challenging task. If the old tub is conveniently accessible, the job can relocate easily; if you have to open a wall to eliminate the old tub as well as place the new bathtub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly require a helper to leave the old bathtub as well as embeded in the new one. Make certain you have actually certified yourself for the job as well as fit attempting it. Instead of working with a contractor to take over a halfway-completed project, it is much better to think about utilizing one prior to you start. Opportunities are you might require a professional plumber to make tube connections.
This short article will help you install a brand-new bath tub in your washroom if you have already purchased a new tub and also do not require to transform the setup of your previous water pipelines.
Your devices and material checklist should consist of the following:
Preparing for the Installation
Firstly, the supporting frame supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to ensure that if the tap comes with a plastic washer, it is fitted in between the bath and the taps. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets device to stop stress on the bathtub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you use every one of the provided washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath need to now prepare to be suited its final placement.
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, then the first thing you must do is disconnect the water system. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The process of eliminating the existing taps can be quite troublesome as a result of the limited access that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a towel ready for the staying water that will originate from the pipelines. Once the supply pipelines have actually been eliminated, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from transforming during this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any kind of old securing compound.
Prior to going on to fit the new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Tub
Using both wooden boards under its feet, position the bath tub in the called for setting. The wood boards are valuable in equally spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 tiny points.
The next objective is to make sure that the bathtub is leveled all round. This can be attained by examining the spirit level and changing the feet on the tub till the level reads degree.
To set up faucets, fit the bottom of the outermost adaptable faucet port to the appropriate supply pipeline by making a compression join; after that do the exact same for the other faucet.
Switch on the water as well as check all joints and also brand-new pipework for leaks and also tighten them if needed. Fill up the bathtub as well as likewise check the overflow electrical outlet as well as the regular outlet for leaks.
Finally, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bath tub ought to wait till the bathtub has actually been used at the very least once as this will resolve it into its last position.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic connector to stop damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin ensuring that the washers remain in location between the tap and also the sink. Protect the faucet in place with the manufacturer supplied backnut. Once the faucet is securely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal tap adapters. The former type needs to be connected to the tap finishes first, tightening up only by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bathroom meets the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to break a stiff seal, creating the water to penetrate the wall in between the bathroom and also the tiling, resulting in complications with dampness and also possible leaks to the ceiling below.
You can select from a selection of coloured sealants to blend in your fixtures as well as installations. They are marketed in tubes and cartridges, and are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill the tub with water before securing, to permit the activity experienced when the bathtub remains in usage. The sealant can crack rather very early if you do not consider this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily offered on the market. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
As a devoted person who reads on A Step-by-Step Guide to Installing a Bathtub, I figured sharing that excerpt was worth the trouble. Do you know about another person who is fascinated by How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Be sure promote it. I am grateful for your time. Visit us again soon.
Get Quote Now
Report this page